///////////////////////////////////////////////////////////////////////////

    - Star Windows Software V3.7.0 -
        Readme File                                       06/24/2024

   (C) 2015 - 2024 Star Micronics Co., Ltd. All rights reserved.
///////////////////////////////////////////////////////////////////////////

*This ReadMe File applies to Star Windows Software V3.7.0.

  Thank you very much for purchasing Star Printer.

  Contents:

    1.  Supported Models
    2.  Functions and Models
    3.  How to Install, How to Uninstall
    4.  Silent Installation
    5.  Silent Un-Installation
    6.  OPOS Settings
    7.  Restrictions
    8.  Software Evaluation Environment
    9.  Release Notes


    ====================
    1.  Supported Models
    ====================
     This Software supports the following Star Micronics Printer models:

     - mC-Print2
     - mC-Print3
     - mPOP
     - TSP100IV
     - mC-Label3
     - BSC10II (Standard mode)

    ========================
    2.  Functions and Models
    ========================
     The available features vary depending on models and interfaces.
     Please see installation manual for futher details.
     When using OPOS, refer to Section 6, OPOS Settings.


    ====================================
    3.  How to Install, How to Uninstall
    ====================================

    Turn the printer off and close all other applications that are currently
    open before installing the Star Windows Software.

    Please refer to an installation manual for the procedure of 
    installation and uninstallation.

      Star_Windows_Software_V3.7.0_setup\Document\Install Manuals\Star_Windows_Software_InstallManual_en.pdf


    =======================
    4.  Silent Installation
    =======================
    By running a silent installation, the software can be automatically
    installed without operator action or onscreen feedback. This is
    convenient when performing installation on several PCs. 
    To begin a silent installation, run
    "msiexec.exe /i [file name of msi(with full path)] /qn"

    Execute command prompt as administrator.

    msi file is in "\Setup" folder in the zip file.

    <Windows 10 (32bit) >
     msiexec.exe /i Star_Windows_Software_V3.7.0_setup\Setup\StarWindowsSoftware-3.7.0-3.7.0-Release_x86.msi /qn /norestart

    <Windows 10/11 (64bit) >
     msiexec.exe /i Star_Windows_Software_V3.7.0_setup\Setup\StarWindowsSoftware-3.7.0-3.7.0-Release_x64.msi /qn /norestart


    ==========================
    5.  Silent Un-Installation
    ==========================
    By running a silent un-installation, the software can be automatically
    uninstall without operator action or onscreen feedback.
    This is convenient when uninstalling this software from several PCs. 

    To run a silent un-installation, run "msiexec.exe" with the following
    command.

    (1)Execute command prompt as administrator.

    (2)Execute the following command to run a silent un-installation.

       msiexec.exe /x {AFE3B9EA-BD76-4339-844F-FD80360EDC46} /qn

    (3)If you are using the Star Micronics Cloud Service, execute the following command 
       to delete the registration information (the confirmation screen will not be displayed).

       [SMCSInformationCleanUpTool.exe(*1)(with full path)] /q


    By executing "SilentUninstall.bat(*1)" included in this package as administrator,
    the above (2) and (3) can be executed continuously.


    *1:It is stored in the following folder in this package.

         Star_Windows_Software_V3.7.0_setup\SMCSInformationCleanUpTool


    ======================
    6.  OPOS Settings
    ======================

    6-1  USB Printer Class
      Remove the check next to 'Enable bidirectional support' located in
      the ‘Ports’ tab of the printer driver's Properties window (Right click > Properties).
      Please set the Memory Switch to 'NSB Enable' from Printer Settings.

    =============================
    7.  Restrictions and Cautions
    =============================
    Below are the restrictions and cautions for this version.

    <Install, Uninstall>
    Note the following points when uninstalling software.

     - If an existing futurePRNT installation has been on the system, 
       the silent installation will be interrupted.
       To perform the silent installation, uninstall futurePRNT at first.

       *The settings made with TSP100 Configuration Application will be deleted 
        when futurePRNT is uninstalled.
        If necessary, it is recommended to save the settings using the export function of
        TSP100 configuration application before uninstalling.
        For details, please refer to the software manual of futurePRNT.

     - StarMicronics folder
       In some cases the following folders do not delete after the driver is uninstalled:
           [Start Menu] -> [All Programs] -> [StarMicronics]
           32bit Windows:   C:\Program Files\StarMicronics
           64bit Windows:   C:\Program Files (x86)\StarMicronics

       They can be manually deleted. (Right Click > Delete)


     - Installing this software may fail if Windows Update is installing updates 
        on the computer at the same time as Setup is running.
        To remedy this issue, wait for Windows Updates to finish, and then restart  
        the computer. Then, run setup.

     - Install after uninstallation
       Install after uninstallation, delete "old" connection settings, then make new connection.


    <Printer Driver>
    
     - If the Printer Queue Name is changed after a USB Printer is already installed
       using the USB Printer Class Driver, it is necessary to reboot the PC.
        
     - In some applications (e.g. Microsoft Office),  you may not be able to change 
       the paper size from the UI in the applications.
       In this case, please set the paper size from "Printer properties" first.
       Then you can select the paper size from the UI in the applications.

     - If you make the following settings on the [Printer properties]-[Advanced] tab,
       printing may not be performed properly, so do not change to the following settings.

       - Print directly to the printer
       - Uncheck "Enable advanced printing features"

     - When creating a user-defined paper, the left margin may not be set correctly.
       In this case, set the print mode to "Line" on the [Printer Properties] - [Device Settings] tab,
       and the left margin will be set to the correct value.

    <Printer Utility>
     -  When changing Memory Switch Settings, ensure the printer power is on.
        
    <Printer Utility - Windows Printer Queue Management>
     -  When adding the windows printer queue of bluetooth printer, it may fail with error message
        "Could not add the printer queue.".
        In this case, please reboot your computer and add printer queue again.
        After rebooting, if adding printer queue still fails,
        please add printer queue using Windows standard function.

        *How to add printer queue using Windows standard function

            1. Open "Controll Panel" from Apps. Then Select "View devices and printers" 
               and click "Add a printer".
            2. Click "The printer that I want isn't listed".
               Select "Add a local printer or network printer with manual settings" and click "Next".
            3. Select the COM Port (made by pairing with the printer : ex COM3) from "Use an existing port"
               and Click "Next". If the COM port doe's not listed, select "Create a new port" and "Local Port",
               then type COM port name.
            4. Select "STAR" from "Manufacturer", and select your printer from "Printers". 
            5. Select "Use the driver that is currently installed" and Click "Next".
            6. Type a printer name, and Click "Next".
            7. Click "Finish" and close the wizard.

    <Printer Utility - OPOS>

     - For customer who already installed StarPRNT Intelligence, SMJ OPOS Register 2009, 
       StarPRNT Intelligence for Portable or SMJ OPOS Register for Mobile.
       
       After install this software, additionally, please do not uninstall above-mentioned sotfwares.

       By uninstallation the softwares, the device informations which already registed by this software, 
       will be removed because these softwares use common Service Object(SO) and Common Control Object(CCO).

    <Printer Utility - Logo Store>
     -  When storing the multiple logos, it may fail with error message "Failed to send data.".
	      In this case, please clear all logos first.
	      After clearing all logos, please store logos again.
  
    <Bluetooth Interface>
     -  When using printer with Bluetooth Interface, please confirm Auto Connection setting.
        According to your device OS, the setting should be as follows:
        
        Auto Connection OFF : Windows, Android, Linux and Mac
        Auto Connection ON  : iOS
        
     -  How to change Auto Connection setting
        Windows : Please use "Star Bluetooth Utility" installed with Printer Utility.
                  (Please refer to "BluetoothUtility_Win_en.pdf".)
        iOS     : Please use "Star Quick Setup Utility" from AppStore.
        Android : Please use "Star Quick Setup Utility" from Google Play Store.

        Linux, Mac: We are sorry that no setting tool is available.
        Please prepare one of the above OSs environment to be able to make use of those tools.
        
    ===================================
    8. Software Evaluation Environment
    ===================================
     This software has been evaluated mainly on the following environments.

    PC environments 
         CPU : Intel Core i7 11700K (3.6GHz)
         RAM : 16GB
         SSD : 250GB

    Windows environments 
      - Microsoft Windows 10 Enterprise          (32bit)
      - Microsoft Windows 10 Enterprise          (64bit)
      - Microsoft Windows 11 Enterprise          (64bit)

    ==================
    9. Release Notes
    ==================
    Rev. 3.7.0  Add support BSC10II.
    06/24/2024  Add label paper size setting utility "Label Setup".
                Printer Settings
                 - Support for automatic external device drive (TSP100IV Firmware V2.2 and later).
                Star CloudPRNT Settings
                 - Support for HTTP Response Timeout (TSP100IV Firmware V2.2 and later).
                OPOS (Scanner SO)
                 - Improve reading speed.

    Rev. 3.6.0  Add support POP10CBI.
    02/22/2024  Windows Printer Driver (mC-Label3)
                 - Added "Tear Off" in Paper Cut(Document Bottom) setting.
                 - Changed to feed paper to the mark position when the printer driver setting is 
                   the default value and the mC-Label3 setting is set to use the gap sensor or black mark sensor.
                Windows Printer Driver (TSP100IV)
                 - Fixed an issue where the width definition was incorrect for the following paper sizes.
                   50.8mm x 200mm / 50.8mm x Receipt
                   51mm x 200mm   / 51mm x Receipt
                   If there is a problem with the printout when using the above paper size, 
                   please delete the above papers from "Print Server Properties" before doing the upgrade installation.

    Rev. 3.5.1  Bug Fix
    10/24/2023   - Fixed a bug that the bug fix in Rev. 3.3.0 that was not reflected in Rev. 3.4.0 or later.

    Rev. 3.5.0  Add support MCP31CI and MCP31CBI.
    10/16/2023  Bug Fix
                 - Change Media Type(mC-Label3)
                  - Fixed test printing failure after selecting die cut label.

    Rev. 3.4.0  Add support TSP100IV SK.
    09/07/2023

    Rev. 3.3.0  Advanced Settings function:
    05/30/2023   - MCL32: Added USB-C function support.
                SteadyLAN Setting Utility
                 - Added MCL32 support.
                Bug Fix
                 - Windows Printer Driver(mC-Label3)
                  - Fixed bugs that the paper is not fed to the mark position 
                    when the Paper Cut is set to No Cut with the gap sensor or black mark sensor is enabled.

    Rev. 3.2.0  Add support MCL32(mC-Label3 Series)
    04/10/2023

    Rev. 3.1.1  Software Installer
    10/28/2022   - Partially changed the uninstall process.

    Rev. 3.1.0  Add support POP10CI(mPOP Series)
    05/10/2022   - Printer Utility
                   Change the supported function name from Connect Printer to Cloud to Printer's Network Settings.

    Rev. 3.0.0  Release as Star Windows Software
    10/29/2021   - Update from StarPRNT Intelligence for mCollection.
